This mount is able to be used for all directv and dish network dishes including but not limited to the Dish 500, 18" round dish w/ dual lnb, and the Slimline dish antenna. 

This mount is the replacement for the NPR6B.

This mount even has a place to bolt support braces for slimline dish.

There is a place to bolt your mast right on the frame making this easy installation with no waste.

This mount does not include mast or support braces

Hot Shot Satellite Dish Heater Power Supply, 7 amp

Each
4.50 in. wide x 4.00 in. high x 7.50 in. deep
Volume: 135.00 cubic in.
Weight: 6.58 lbs

Even if your Hot Shot Satellite Dish Heater is working fine keep us in mind for ALL your satellite replacement parts. Satellite Dish Heaters, Multi Switches, and Satellite Mount s.  We carry it all. 

Order Online or Call 330-633-7133 Today!

Simply secure this heater element to the top of your lnb arm to prevent snow and ice build up on your HughesNet satellite antenna.
Elements for Hot Shot heater are powered by a transformer from a Hot Shot dish transformer.

Secure this Hot Shot heater element for the feedhorn of your HughesNet antenna to prevent ice and snow from building up on your antenna in the winter. The element is powered by the transformer from Hot Shot dish antenna.

Keep the winter snow and ice off your satellite dish, with this innovative Hot Shot heater for 38" ellipticals and HughesNet satellite antennas.

This low voltage satellite antenna heater keeps your dish free and clear of snow and ice and you stay warm in your house!

• Completely automatic operation
• Patented heating technology
• Easy to follow installation directionss
• Thermostatic temperature sensor turns the heater on in cold weather automatically
• 100 feet cable included with the kit
• Low voltage power supply to power the advanced heating element
• Self-adhesive heating element to keep the dish clear
• Durable all weather outdoor grade materials

The Hot Shot satellite antenna heating element pad is perfect for those that already have a satellite dish antenna installed, as it is installed in a snap. It is very easy to setup and provides durable protection from snow and ice buildup on your satellite antenna.

Hot Shot Dish Heater Arm Element

This attachment plugs right into your Hot Shot Dish heater at the dish.  Keep the arm free of snow too.

This satellite dish heater kit fits all 24 inch dish antennas and is a snap to install.

Keep your satellite dish free from snow and ice buildup with this innovative Hot Shot 24" heated satellite antenna kit.

This low voltage satellite antenna heater will keep your dish free from snow and ice and you warm and cozy in your house!

• Totally automatic operation
• Patented satellite dish heating technology
• Easy to follow and simple installation instructions
• Thermostatic temperature sensor to start the heater on in cold weather automatically
• 100 feet of included cable
• Low voltage power supply to power the heating element
• Self-adhesive dish heating element
• Durable all climate outdoor material

The Hot Shot satellite antenna heating element pad is excellent for installation on existing satellite antennas, as it is installed in a snap. This very simple to install heater provides durable all weather protection from snow and ice buildup on your dish antenna.

The Slimline Dish Heater Kit from Hot Shot will keep your satellite dish antenna clear from collecting ice and snow in the deepest of winter months.

This satellite dish heater has a built in sensor which automatically turns on the heater in freezing conditions. The self adhesive dish heating element will help prevent signal loss service outages caused by snow and ice building up on your dish.

The Hot Shot heater can also reduce rain fade by up to 75 percent. Simply attaching the self adhesive vinyl heating pad to your satellite antenna and enjoy better service in all weather conditions.

*This heater works on slimline type dishes.

• DIRECTV 5 LNB Slimline
• DIRECTV 5 LNB (AT9)
• DIRECTV DTV66E International
• HughesNet
• WildBlue
• Dish Network 500+
• Dish Network 1000+

  This Hot Shot Dish Heater Kit includes:

  • 100 Feet of cable
  • Automatic thermostatic temperature sensor
  • Easy to follow installation instructions
  • Durable all weather outdoor quality materials
  • Safe low voltage power supplies
  • One transformer connection

This brilliant heating kit fits all 18 inch dish antennas and can also be used for the 18 x 20 inch phase 3 antenna as well.

Keep snow and ice cleared from your satellite dish, with this fully automatic Hot Shot heated satellite 18" antenna kit.

This low voltage antenna heater will keep your dish clear of snow and ice in the fiercest of winter conditions!

• Completely automatic operation
• Patented satellite technology
• Easy to use installation instructions
• Thermostatic temperature sensor to initialize the heater in cold weather automatically
• 100 feet of cable is included
• Low voltage power supply to power up the heating element
• Self-adhesive heating element to effectively heat the dish
• Durable all weather outdoor rated material

The Hot Shot satellite antenna heating element adhesive pad is great for previously installed satellite antennas and is setup in a snap. Very easy to install and reliable protection from snow and ice buildup on your antenna make this the perfect solution.

Cable Assembly for Hot Shot Satellite Dish Heaters, 100 ft w/plug

Dog chewed on your Hot Shot Satellite Dish Heater Cable?  We carry the most complete line of Hot Shot Satellite Dish Heaters and accessories in the industry.  Even if your Hot Shot Satellite Dish Heater is working fine keep us in mind for ALL your satellite replacement parts.  We are committed to serving our customers.

Order Online or Call 330-633-7133 Today!

This switch is great for switching between components that use coaxial cable.  Great for switching between cable or satellite boxes, vcrs, TVs and more.  The push button design makes this switch easy to use for anybody.

This is a 4 pack of Directv Slimline SL5S SWM Dishes for reception of 99, 101, 103, 110, and 119 satellites.

Includes

4x  Reflectors

4x  Back Plates

4x  Back Assemblies (AZ/EL Mount)

4x  Slimline Mounting Poles w/ Foot

4x  Hardware Packs

4x  LNB Arms

4x  SL5S SWM LNBs for 99,101, 103. 110, and 119 Satellites

This is a 4 pack of Directv Slimline SL5 Dishes for reception of 99, 101, 103, 110, and 119 satellites.

Includes

4x  Reflectors

4x  Back Plates

4x  Back Assemblies (AZ/EL Mount)

4x  Slimline Mounting Poles w/ Foot

4x  Hardware Packs

4x  LNB Arms

4x  SL5 LNBs for 99,101, 103. 110, and 119 Satellites

This is a 4 pack of Directv Slimline SL3S SWM Dishes

Includes

4x  Reflectors

4x  Back Plates

4x  Back Assemblies (AZ/EL Mount)

4x  Slimline Mounting Poles w/ Foot

4x  Hardware Packs

4x  LNB Arms

4x  SL3S Single Wire LNBs for 99,101, and 103 Satellites

This is a 4 pack of Directv Slimline SL3 Dishes

Includes

4x  Reflectors

4x  Back Plates

4x  Back Assemblies (AZ/EL Mount)

4x  Slimline Mounting Poles w/ Foot

4x  Hardware Packs

4x  LNB Arms

4x  SL3 LNBs for 99,101, and 103 Satellites

and

8x  Support Braces

The Viewsat Ultra Lite is the replacement for the Viewsat Lite or Viewsat 2000 Platinum Lite. Viewsat Ultra lite has the great advanced user friendly features like the Viewsat ultra but at a lite cheap price. In order to engineer this, Viewsat took the Viewsat Ultra and trimmed the fat.

Viewsat Ultra lite does not include a card reader or Dolby output. Standard remote is included. Viewsat Ultra. The Viewsat Lite is Viewsat's entry level model at a fantastic price for those looking for a high quality Korean built Free To Air receiver.

The Viewsat Lite features a conexant Main Processor running at 160 MHz, 32mb of SDRAM for an industry leading on-screen channel guide, blindscan (smart search), and is 100% compatible with Viewsat Lite Ultra firmware and channel lists. S-Video RCA outputs usb 2.0 drive data port and much more.

• USB 2.0 Port
• 2 times more ram then Platinum Lite
• Great Support
• S-Video
• RCA Audio Video hook ups

Viewsat Ultra Lite Features:

• USB 2.0 Port
• Fully MPEG-2 & DVB Compliant
• Input Frequency 950-2150MHz
• Supports EPG, PIG
• Supports SCPC & MCPC from C / Ku-band
• 1 LNB Input Tuner with Loop Through IF Signal
• Tuner Symbol Rate: 1-45MS/s
• Fast Booting & Auto Scan
• Quick Channel Changing
• Max. 4000 Channels (TV & Radio) Programmable
• User Friendly 256 Colors OSD & Easy GUI
• A lot of OSD Language supported
• Radio Channel Background Display
• Favorite Channel List Programmable
• Master PIN Code Function & Parental Lock Function
• 100 Steps Volume Control
• Automatic Detection of Forward Error Correction
• Window based S/W Download Program Supported by RS232 Serial Port
• Set to Set Download (Main Program, Channel Data)
• 4:3, 16:9 Letter Box & Teletext using OSD
• 7 Segment-4 Digit Display
• 3 Keys on the Front Panel (Power On/Off, Channel Up/Down, Volume Up/Down)
• Various LNB Polarity Control
• 22KHz Switching Control
• RCA Output for Video, Audio L/R
• S-VIDEO Output
• RF-Modulator Output
• Power Switch

This signal meter has 22 khz tracking and an internal Battery Pack.

Also included

• Convenient carry strap
• Wall plug charging unit
• Meter and variable frequency audio tone
• Dish aligned for maximum meter deflection or highest pitch tone
• Gain control allows a range of input signal levels
• Battery Pack 13/18 volt so this meter can be used without a receiver for ease of installation

With this voltage upgrade you can easily align WildBlue and Telesat / Anikast / Xplornet antennas without connecting to the modem! Get your dish pointed before you have to start running any modem cables and doing your provisioning. This gives you the ability to power the TRIA with your Super Buddy or Sat Buddy meter.

For use with the following systems:

• WildBlue
• Telesat/Anikast/Xplornet

Features include:

• Power the WildBlue and Anikast/Xplornet/Telesat TRIA with your satellite meter
• Weather Resistant and Rugged durable aluminum case with rubber gaskets

Applications:

• WildBlue & Telesat/Anikast/Xplornet Installations
• Site surveys
• Commercial installations
• Single family home installations
• Multiple dwelling unit (apartment and condominium) system installations and alignments

Specifications:

• Enclosure: Aluminum with rubber gasket sealed end panels
• Size (L x W x D): 2.8" x 2.8" x 1.3" - (7.1 cm x 7.1 cm x 3.3 cm)
• Weight: 0.6 lbs. (0.27 kg)
• Connector Style: F-female
• Temperature Range: 0° to 125° F (-18° to 52° C)
• Input Voltage: from sat meter, 13 to 18 VDC
• Input Current: 600 mA maximum @ 13V
• Output Voltage: Tx port 32 VDC, Rx port 26 VDC
• Cable Length: Recommend short jumper, 100' max, RG-6
• Output Current: 150 mA max (combined both ports)
• Passes RF Signals: 950-2150 MHz, -60 to 0 dBm
• Insertion Loss: 0.4 dB (974 MHz), 1.1 dB (1563 MHz)
• Return Loss: 10 dB (typical)
• Impedance: 75 Ohm
• Warranty: 12 month limited

NOTE: The Blue Bunny Voltage Step Up is only compatible with WildBlue TRIAs manufactured by UMA in Taiwan. Please check the tag located on the bottom of your TRIA to see if it’s compatible with the Blue Bunny Voltage Step Up. If it says "Made in Taiwan by UMA", then it is compatible. If it says "Made in Korea by Ko Space", then it is NOT compatible

The Birdog Ultra satellite meter is by far the best meter on the market.  This meter gives you the ability to setup any satellite antenna.  This meter has a zip code lookup, USB port, 6 hours of battery life, and more. If you want the best meter on the market this is the way to go. • The perfect meter for the any installer

• New battery provides complete power solution: Li-Pro Lithium Polymer battery gives you up to six hours of battery life or 20 Wild Blue alignments

• Only meter that locks on WILD BLUE

• LNB supply 13 and 18V @ 250mA

• Uses new DMTC technology to pinpoint and lock on Wild Blue Streams

• New Constellation Diagram: Allows you to check for noise on long runs No more questions on your run being to long plug the Ultra in and find out

• Zip Code Look up: No matter where you are at in the country finding your look angles is now as easy as putting in the zip code right on the job site

• Featuring: All-In-One Zip Code Look Up, Spectrum Display, Expanded Mesurement Display, All-In-One Power Solution and a new Constellation Diagram

• Data log

• LNB/Cable Test

• DTV SWM Histogram Function can show up to 9 simultaneous carrier/frequency measurements

• Specifically designed for SWM Technology

• Version: Ultra

• Expanded measurement display for use with WildBlue installations

• 2.1mm Female PSU plug for external charge

• Universal charger 80 to 250V AC

• Spanish language display options

• Easy-to-Ready display with digital enhanced graphics

• Recalls last satellite position upon power-up

• Clear and Easy to use Spectrum Analyzer

• QPSK Constellation diagram

• Twice the satellite memory positions

• RF input range: 950 - 2150MHz

• Input dynamic range: - 65dBm to -25dBm

This meter is ready to use out of the box (Battery is Charged and Satellite Database is Loaded)

Extras include:

• Field Replaceable F - connectors (barrel connectors)
  
• Calibrated Signal Level (dBm, dBmV or dBµV)
• Holds ALL satellites and ALL their transponders
• Ability to LOCK on WildBlue internet satellite and able to identify relevant geographic specific WildBlue spot beam based on your Zip Code
  
• Ability to LOCK on new Dish Network 118.7 and 129 satellites with 8PSK signals
• Ability to do new DIRECTV Slimline / AT9KaKu Installs (Can LOCK on and display signal strength for 101, 110, and 119 and will display signal strength for 99 and 103)
• Ability to do new DIRECTV MFH1 and MFH2 Installs
• Ability to control new Zinwell 6x8 Multiswitch
• Ability to save proof of performance readings (actual signal level & quality measurements) and then upload them to your PC to give to the head office
• BER (Bit Error Rate, Reed Solomon)
• Zip Code Lookup - Ability to obtain needed azimuth, magnetic heading, and elevation for antenna install preparations based on your Zip Code
• Tunable to individual transponders
• Quick Charge Battery
• Ability to manually enter new custom satellites using front panel keypad (ideal for lab use or military classified satellite use)
• Rugged durable aluminum case with rubber shock guards and weatherproof gaskets
• Troubleshooting ability (Can display Voltage supplied by IRD, Current drawn by LNB, and LNB Frequency Deviation to find defective drifting LNBs)
• Works with both normal and stacked frequency plans
• Current Limit Level of 600 mA; This is enough juice to power even the Dish Pro Plus 3 LNB setup and the Dish 1000.2, which are the "current hogs" of the industry

Ideal for Use with the Following Satellite Systems:

• Dish Network (including new Dish Network 118.7 and 129)
• DIRECTV (including new DirecTV Slimline / AT9KaKu, MFH1, and MFH2 Systems)
• Bell ExpressVu
• Tachyon
• All Low Ku Band FSS Satellites (i.e., Globecast / Telstar 5 / IA5 / Galaxy 25)
• DirecWay / HughesNet
• DTN
• Star Band
• Star Choice
• WildBlue
• C-Band
• Custom
• Stacked LNB / L-Band (i.e. Sonora systems, NAS systems, etc.)

Meter Features:

• ID the satellite by "align-to-lock" or "automatic scan"
• Positive ID multi-lock algorithm eliminates false positives
• Geo-sensitive "Field Guide" software stores all satellites and transponders per global region
• Zip code entry provides antenna azimuth and vertical angle settings
• Field replaceable connectors
• Audible tone for signal lock and peak
• Tunable to individual transponders
• Quick charge battery with universal AC or vehicle 12 VDC
• Controls multi-LNBs/switches with 22kHz/DiSEqC
  
• Easy to use single function front panel buttons
• Displays cross-pole value from DIRECWAY modems
• Able to manually enter new satellites using front panel keypad
• Computer interface for future upgrades
• Rugged durable aluminum case with rubber shock guards
• Applications
  • VSAT installations
  • Site surveys
  • Commercial installations
  • Single family home installations
  • Multiple dwelling unit (apartment and condominium) system installations and alignments

Meter Measurements

• Signal Level (dBm, dBmV or dBµV) with present and peak bargraph
• Signal Quality (displayed with familiar IRD value with present and peak bargraph or as C/N, Eb/No, or Es/No)
• Carrier/Noise Ratio (dB)
• Bit Error Rate (Post-FEC, Reed Solomon)
• Voltage supplied by IRD
• Current drawn by LNB
• LNB Frequency Deviation

Meter Specifications

• Frequency range: 950 to 2150 MHz
• Tuning resolution
• Individual Transponders
• Signal level range: -70 to -10 dBm (-21 to +39 dBmV) (+39 to +99 dBµV)
• Signal lock formats: DSS, DVB-S, Digicipher 2, Dish 8PSK
• Impedance: 75 Ohm
• LNB power: 13 VDC for V/R, 18 VDC for H/L, Current limited at 600 mA
• Switch control: 22 kHz, DiSEqC, DISH Legacy
• Battery
  • Rechargeable NiMH 7.2V, 3.0 Ah
  • Run time/charge: 3 hours for a single LNB (depends on LNB current draw)
  • Universal AC charger
  • 100 to 240 VAC, 50/60 Hz, fast charge and then trickle
  • Vehicle Charger
  • 12 VDC
• Computer interface
• Serial Port (Com 1, 2, 3, 4, 5 or 6)
• RF Connector
• Double-F barrel field replaceable
• Size (W x H x D): 6.8" x 6.4" x 3.2", (17.3cm) x (16.3cm) x (5.8cm)
• Weight: 3.45 lbs. (1.6 kg)
• Operating temperature: 0°F to 125°F (-17°C to 51°C)

Standard Meter Accessories

• Shoulder strap
• Cordura protective flap (yellow color)
• AC Line Cord for charging battery (Universal 100 to 240 VAC Transformer is built into the meter)
• Automobile cigarette-lighter adapter battery charge cord
• RS-232 PC Download Cable (9 Pin Serial Connector)
• Operator’s Manual
• Application Notes (Detailed Instructions for Specific Installations)
• System Selection Trees (Software Tree Maps Displaying the Meter's Setting Options)

Optional Accessories

• Blue Bunny Voltage Step-Up - for use with WildBlue & Telesat/Anikast/Xplornet

Competitive Features:

• Durable Rubber Shock-Absorbing case with carabineer clip - longer lasting than neoprene cases
• Weather resistant tough aluminum extrusion enclosure with rubber gaskets vs. cheap plastic enclosure of competition
• Loud audible tone
• High Current Limit Level of 600 mA that allows it to work with the Dish Pro Plus and Dish 1000.2
• Internal Rechargeable 12 cell NiMH 300 mAh Battery
• Ability to see battery level remaining

Features:

• NEW! Heavy-Duty Field Replaceable F-Connectors (easy change with one 7/16" wrench)
• Bright LED display, easy to read even in direct sunlight
• Strong audible tone
• Internal rechargeable NiMH battery
• Able to power LNB from internal battery or IRD
• Rugged, compact, weather resistant design
• Includes DC Cigarette Lighter Charger, AC Wall Charger
• Short circuit protection
• 950-2150 input frequency
• Tests Coax Cable Runs
• Selectable Audio On/Off
• Able to check IRD Set Top Box Receiver Voltage, LNB current amps
• Works with all LNBs
• Able to align antenna quickly and reliably without the receiver
• Measurements:
  • Signal strength (RF energy 950 to 2150 MHz)
  • LNB current draw (mA)
  • Voltage supplied by the IRD set top box
  • Internal battery voltage
• Specifications:
  • Frequency range: 950 to 2150 MHz
  • Impedance: 75 Ω
  • Measurable input level: -48 to -8 dBm total power, -60 to -20 dBm per transponder
  • Insertion loss: 6 dB (950 to 1450 MHz); 8 dB (1450 to 2150 MHz)
  • Size (H x W x D): 6.5" x 2.7" x 1.1", 1.5 lbs (16.5cm) x (6.9cm) x (2.8cm), 700g
  • Temperature range: 0°F to 125°F; (-17°C to +50°C)
  • Connectors: Type F female, Field Replaceable
• Standard Accessories:
  • Heavy duty rubber case with carabineer
  • Wall transformer for charging battery, 120V or 240V
  • Operator's Instructions
  • Automobile cigarette-lighter adapter battery charger

What makes the Dual Buddy better than other meters?

• Heavy Duty Field Replaceable F connectors that can be swapped out with one 7/16" wrench
• Durable Rubber Shock-Absorbing case with carabiner clip - longer lasting than neoprene cases
• Weather resistant tough aluminum enclosure with rubber gaskets compared to cheap plastic enclosure used on other meters
• High Current Limit Level of 600mA that allows it to work with the Dish Pro Plus and Dish 1000.2
• Loud audible tone
• Internal Rechargeable 12 cell NiMH 300 mAh Battery
• Ability to see battery level remaining
• Bright LED display, easily viewable in direct sunlight
  • Features include:
    • Dual satellite signal strength measurements making it so you can view and align two satellites at one time
    • NEW! Improved Heavy-Duty Field Replaceable F-Connectors (easy change with one 7/16" wrench)
    • 22 KHz tone mode to control multiswitches and multi-LNB dishes
    • Bright LED display, easy to read even in direct sunlight
    • Strong audible tone
    • Internal rechargeable NiMH battery
    • Able to power LNB from internal battery or IRD
    • Rugged, compact, weather resistant design
    • Includes DC Cigaretter Lighter Charger, AC Wall Charger
    • Short circuit protection
    • Switches 22KHz On/Off
    • High Current Limit Level of 600mA that allows it to work with the Dish Pro Plus and Dish 1000.2
    • 950-2150 input frequency
    • Tests Coax Cable Runs
    • Selectable Audio On/Off
    • Able to check IRD Set Top Box Receiver Voltage, LNB current amps
    • Works with all LNBs
    • Able to align antenna quickly and reliably without the receiver

Measurements

• Signal strength (RF energy 950 to 2150 MHz)
• LNB current draw (mA)
• Voltage supplied by the IRD set top box
• Internal battery voltage

Specifications

• Frequency range: 950 to 2150 MHz
• Impedance: 75 Ω
• Measurable input level: -48 to -8 dBm total power -60 to -20 dBm per transponder
• Insertion loss: 6 dB (950 to 1450 MHz), 11 dB (1450 to 2150 MHz)
• Size (H x W x D): 6.5" x 2.7" x 1.1", 1.0 lbs, (16.5cm) x (6.9cm) x (2.8cm), 700g
• Temperature range: 0°F to 125°F, (-17°C to +50°C)
• Connectors: Type F female (field replaceable)
• Power: Uses IRD power when connected, otherwise uses internal battery. IRD voltage loss through the SAT Buddy is 1.3 V. Current consumed by the SAT Buddy is 90 mA.
• LNB Power: Current limited at 600 mA
• Internal Battery Pack
• Rechargeable 12 cell NiMH 300 mAh, 12-16 V nominal, automatic shutoff, 1.8 hours typical use per charge.
• Battery Charge Time: ±10 hours from wall charger
• Wall Charger Output: 12 VDC, 200 mA, center pin positive, 2.1mm I.D
• Signal Measure Mode
  • Signal Level Display
  • Bargraph LEDs left row x 10, right row x 1
  • Audible Tone
  • Dual beep rate with solid tone at peak
• Current/Voltage Mode
• LNB Current Draw: 0 to 500 mA (each LED segment is 50 A)
• LNB Supply Voltage: 10 to 20 volts (each LED segment is 1V, above 9V)
• Standard Accessories
  • Heavy duty rubber case with carabiner
  • Wall transformer for charging battery, 120V or 240V
  • Operator's Instructions
  • Automobile cigarette-lighter adapter battery charger

Features Include

• Heavy Duty Replaceable F-Connectors (easy change with one 7/16" wrench)
• 22 KHz tone mode to control multiswitches and multi-LNB dishes
• Bright LED display, easy to read even in direct sunlight
• Strong audible tone
• Internal rechargeable NiMH battery
• Able to power LNB from internal battery or IRD
• Rugged, compact, weather resistant design
• Includes DC Cigaretter Lighter Charger, AC Wall Charger
• Short circuit protection
• Switches 22KHz On/Off
• High Current Limit Level of 600mA that allows it to work with the Dish Pro Plus and Dish 1000.2
• 950-2150 input frequency
• Tests Coax Cable Runs
• Selectable Audio On/Off
• Able to check IRD Set Top Box Receiver Voltage, LNB current amps
• Works with all LNBs
• Able to align antenna quickly and reliably without the receiver

Measurements

• Signal strength (RF energy 950 to 2150 MHz)
• LNB current draw (mA)
• Voltage supplied by the IRD set top box
• Internal battery voltage

Specifications

• Frequency range: 950 to 2150 MHz
• Impedance: 75 Ω
• Measurable input level: -48 to -8 dBm total power, -60 to -20 dBm per transponder
• Insertion loss: 14 dB (950 to 1450 MHz), 22 dB (1450 to 2150 MHz)
• Size (H x W x D): 6.5" x 2.7" x 1.1", 1.5 lbs (16.5cm) x (6.9cm) x (2.8cm), 700g
• Temperature range: 0°F to 125°F (-17°C to +50°C)
• Connectors: Type F female (field replaceable)
• Power: Uses IRD power when connected, otherwise uses internal battery. IRD voltage loss through the SAT Buddy is 1.3 V. Current consumed by the SAT Buddy is 90 mA.
• LNB Power: Current limited at 600 mA
• Internal Battery Pack: Rechargeable 12 cell NiMH 300 mAh, 12-16 V nominal, automatic shutoff, 1.8 hours typical use per charge.
• Battery Charge Time: ±10 hours from wall charger
• Wall Charger Output: 12 VDC, 200 mA, center pin positive, 2.1mm I.D
• Signal Measure Mode
  • Signal Level Display
  • Bargraph LEDs left row x 10, right row x 1
  • Audible Tone
  • Dual beep rate with solid tone at peak
• Current/Voltage Mode
• LNB Current Draw: 0 to 500 mA (each LED segment is 50 A)
• LNB Supply Voltage: 10 to 20 volts (each LED segment is 1V, above 9V)

Use this meter to tune two satellites at once. The 1008IFD includes two meters in one housing for easy alignment of dual satellite single dish installations. You can use this meter unit at the dish without having to hookup receiver (substitutes receiver power) which makes head end adjustments very accurate. When peaking the dish the signal level can be viewed for both LNB's at the same time, (duo or trimode setups) making alignment quick and easy.

Includes:

• Internal Rechargeable NiCad battery pack
• Carrying strap and case
• Wall plug recharging unit
• 13/18 V Battery pack and charger

This newest version of the Birdog Satellite Meter... the Birdog Plus! This new Birdog USB Plus Signal meter has a Spectrum analyzer and a QPSK constellation diagram. It has twice the memory for satellite locations, USB port, Easy-to-Read display with Digital Enhanced Graphics, One-Touch Buttons for easy use, Over 2 hours on a full charge, Spanish Language option, and recalls the last satellite position when you power it up.

• Puncture code (FEC) 1/2, 2/3, 3/4, 5/6 and 7/8
• 2.1mm Female PSU plug for external charge
• Universal charger 80 to 250V AC
• LNB supply 13 and 18V @ 250mA
• Easy to Read display with digital enhanced graphics
• 30 Day Satisfaction Guaranteed Return Policy
• Recalls last satellite position upon power up
• Clear and Easy to use Spectrum Analyzer
• QPSK Constellation diagram
• The Only Signal Meter Compatible with the NEW DIRECTV SWM-8 (SWM Multiswitch)
• Custom Carrier
• Data log
• LNB/Cable Test
• Dual Display for DTV101/119
• DTV SWM Histogram Function can show up to 9 simultaneous carrier/frequency measurements
• Specifically designed for SWM Technology
• Spanish language display options
• Over 2 hours on a full charge
• Twice the satellite memory positions
• RF input range: 950 - 2150MHz
• Input dynamic range: - 65dBm to -25dBm

Birdog USB Plus Meter & Magnepull Wall Wiring Tool Special Bundle

What a great deal this Birdog Meter Bundle is!!!

One low $50.00 price gets you the Birdog Satellite Meter and add a Magnepull Line Puller, too!!!

The Magnepull is a great product that is changing the satellite wiring industry as we speak. Super strength rare earth magnets are used to magnetically couple a wire or pull line through the drywall allowing the technicians to have complete control without extreme damage. The technician simply attaches the pulling device to the end of the cable and couples it through the drywall to the wire retrieval unit. Once coupled, the technician can move the wire retrieval unit on the outside of the drywall to the desired location and retrieve the wire or pull line.

This system eliminates the use of bulky fish tapes and reduces installation time and labor by up to 70%. The super strength rare earth magnets work well with metal studs and insulation making the tool extremely versatile for use in the electrical wiring, alarm, voice wiring, data cable wiring and audio/video industries as well.

This is the new and improved version of the Birdog Satellite Meter... the Birdog Plus! This new Birdog USB Plus Signal meter has a Spectrum analyzer and a QPSK constellation diagram. It has twice the memory for satellite locations, USB port, Easy to Read display with Digitally Enhanced Graphics, One Touch Buttons for easy use, Over 2 hours on a full charge, Spanish Language option and recalls the last satellite position when you power it up again.

• Puncture code (FEC) 1/2, 2/3, 3/4, 5/6 and 7/8
• 2.1mm Female PSU plug for external charge
• Universal charger 80 to 250V AC
• LNB supply 13 and 18V @ 250mA
• Easy to Read display with digital enhanced graphics
• 30 Day Satisfaction Guaranteed Return Policy
• Recalls last satellite position upon power up
• Clear and Easy to use Spectrum Analyzer
• QPSK Constellation diagram
• The Only Signal Meter Compatible with the NEW DIRECTV SWM-8 (SWM Multiswitch)
• Custom Carrier
• Data log
• LNB/Cable Test
• Dual Display for DTV101/119
• DTV SWM Histogram Function can show up to 9 simultaneous carrier/frequency measurements
• Specifically designed for SWM Technology
• Spanish language display options
• Over 2 hours on a full charge
• Twice the satellite memory positions
• RF input range: 950 - 2150MHz
• Input dynamic range: - 65dBm to -25dBm

Suunto Clinometer and Compass

This instrument can be used to measure the heights of trees, ski slopes, buildings, etc.  In the satellite industry this is the standard inclinometer used is the standard device used by professional installer to go on site surveys.

The main advantage to Suunto Clinometers and Compasses is they have very good needle movement.

The Sonicview iHub Dongle is the newest item from the makers of Sonicview.  This item allows your Sonicview 8000HD, Sonicview 360 Elite, or Sonicview 360 Premier to view family photos, play MP3's or play video games like tetris or chess using your Sonicview remote control. The SV Ihub Dongle is the most advanced serial-to-ethernet converter out today. The SV ihub Dongle also supports media delivery over ethernet via the serial port of your SV 360 Premier, SV 360 Elite, and SV 8000HD. This allows you to receive new firmware updates for your Sonicview receiver as soon as they are posted on  the manufacturer's website.  Just to top it off you will also be able to download new eye catching backgrounds for the OSD of your Sonicview receiver.  So don't wait get yours today!!!

DIRECTV SAT-GO also known as "satellite To go" combines a satellite receiver, antenna and TV all into one carry along unit. Giving you the ability to take your favorite shows with you on vacation, camping, or anywhere else you want to watch TV. With the DIRECTV SAT-GO, anytime you want to watch your favorite DIRECTV programming all you need is a clear view of the southern sky.

• Specifications:
  • Integrated 17 inch LCD monitor and satellite receiver with two speakers
  • Compact and portable flat antenna and satellite receiver
  • DIRECTV programming accessed through a platform based on DIRECTV's D11 set top box
  • Small profile IR remote
  • Component and composite A/V inputs
  • Composite A/V out
  • Satellite in connection
  • Phone Jack
  • USB connection
  • AC and DC capable (cigarette lighter adapter included)
  • Rechargeable, replaceable Li-ion battery ~ 1 hour usage

This Directv slimline dish antenna pack is for use with the AU9, SL3, SL5, SL3S, and SL5S lnbfs.  This pack includes everything you need to setup your dish.

Includes:

Hardware packs

Reflector

Mounting arm

AZ EL mount

Back plate

Mast

and

Support braces

REFLECTOR :

• Type: Offset
• Offset Angle: 22.75 0
• Diameter Short Axis: 75 cm
• Diameter Long Axis: 83 cm
• Aperture Efficiency: 75% min.
• KU Band Gain @12.5 GHz: 38.24 dB
• F/D Ratio: 0.65
• Focus Length: 492 mm
• Material: Galvanized Steel
• Finish: Polyester Powder Coating
• Color: Cool Grey

MOUNTING:

• Mounting Type: Ground, Pole & Wall Mount
• Adjustment Type: AZ / EL
• Elevation Angle Range: 12° - 72°
• Azimuth: 0° - 360°
• Pole Diameter Acceptable: 38" 65 mm
• Net Weight: 6.9 kg

ENVIRONMENT:

• Operational Winds: 25 m / sec
• Survival Winds: 50 m / sec
• Ambient Temperature: -40°C ~ +60°C
• Relative Humidity: 0 ~ 100 %

16GA 2" diameter galvenized steel pole for mounting satellite dishes.  This pole can be used to mount Directv AU9 and SlimLine dishes. This pole is 5 1/2 ft. tall.

Use for:

Directv Slimline Dish Antenna

DIRECTV DVR Starter Bundle

This complete startup bundle includes every thing you will need to get your satellite television system up and running. (1) DIRECTV Digital R15 PLUS DVR receiver complete with with IR remote and necessary cables. This is a new receiver and will go under DIRECTV's lease program upon activation, in turn serves as insurance while activated. Also included in this great package is (1) 18 inch round dish with dual LNB.

Upon Activation All DIRECTV Receivers Become Leased Equipment.

We do not ship DIRECTV equipment outside the United States.

18 Inch DIRECTV Dish and Receiver Bundle

This DIRECTV bundle kit comes with everything you will need to setup your satellite TV system! Included in this affordable satellite TV bundle are: (1) DIRECTV D11-500 Digital Satellite Receiver, complete with an IR remote and necessary cables. This satellite receiver is new and will go under DIRECTV's lease program, which in turn serves as insurance for your receiver while it is activated. Also included in this package is (1) DIRECTV 18 inch round dish with dual LNB.

*Upon Activation All DIRECTV Receivers Become Leased Equipment.

*We do not ship DIRECTV equipment outside the United States.

This new Slimline Dish from DIRECTV is smaller, lighter and better looking. It encompasses three LNBs to receive 101°, 110°, 119° degree satellite, plus the new Ka Satellite (99°, 103°) for local HD MPEG4 programming.
• To be used to pick up high definition local channel programming from DIRECTV
• Slim Profile makes this dish aesthetically pleasing for areas with Home Owners Association
• The wind load of this dish is too much for standard tripods, we only recommend Heavy Duty Satellite Tripods
• Dish size: 22.5 in. x 32.5 in.
• Includes the Azimuth/Elevation mount and support braces
• Manufacturers may vary. All components are Directv approved manufacturers.
• Four outputs carrying satellite signal from all Five satellites in the sky
• Heavy duty J-Mount with 2" outer diameter mast opening
• Capable of receiving DIRECTV satellite signals on the Ku band (101°, 110°, 119°) and Ka band (99°, 103°)
• LNB arm with LNBS attached extends 23.5" from the dish surface area
• If connecting more than 4 tuners you will need to use either a WB68 6x8 Multiswitch or a WB616 6x16 Multiswitch

DS4062 RCA style DirecTv Supported 24" (60cm) dish antenna

This antenna is great if you need some extra gain for your Standard Definition DIRECTV antenna. This antenna will hold a dual output lnb for DIRECTV. It is not designed to hold the Dish Network D-Tube style lnbfs.


Effective aperture 60 cm (23.7 in)

Antenna height 70 cm (27.4 in)

Antenna width 64 cm (25.3 in)

Galvanized steel 21ga

This is the ultimate in high end home theater equipment to take full advantage of your DIRECTV high definition programming. Colors are much brighter and more vibrant, sounds are crisper and more realistic, and... To top it all off this receiver records an unbelievable 500 Gigs of media using one of the most intuitive controls on the market.

Features:

• Can record up to 400 hours of standard definition, and up to 100 hours of (MPEG-4) HD programming
• The HR21PRO receiver does not require a lease agreement
• Simultaneous SD and HD output from the same HD signal
• Broadband-enabled to download programming via DIRECTV on Demand
• Ethernet enabled for networking with home PCs via DIRECTV MediaShare
• Optical HDMI allows up to 200 meters between HDTV and HD DVR (Great for use with Owlink Fiber Optic Cable)
• Multiple control options include: RS232 serial connection integrates with home communication system, back-panel IR input for IR extender, switchable IR/RF remote with back lit keys
• Gold plated connectors
• Dual fans for enhanced cooling
• Rack mount or set-top installation Pre-order only

DirecTV High Definition DVR HR23

DirecTV's newest high definition recorder is out and packed with a ton of features.

The HR22 comes with MPEG-4 format compatibility, multiple screen format resolutions, and DIRECTVs popular DIRECTV+ PLUS DVR technology.

• The DIRECTV HR23 includes two satellite tuners for access to both Standard Definition and High Definition programming.
• The DIRECTV HR23 supports 480i, 480p, 720p, 1080i picture resolution outputs and multiple screen formats.
• 500gb Hard Drive Allows you to record up to 400 hrs of Standard Definition programming, up to 100 hours of High Definition programming in MPEG-4 format.
• Pause live TV for up to 90 minutes, use rewind, instant replay and slow motion on live or recorded TV.
• Take advantage of DIRECTV interactive features like DIRECTV ACTIVE.
• As of 3/1/06 DIRECTV now requires a 24 month commitment and all equipment must be returned to DIRECTV® if customer cancels service with DIRECTV.
• Does not have built in ATSC tuner.
• Watch whatever you want on your own schedule. Store your favorite programs, whether standard definition or high definition.
• We will not ship outside of the United States.
• HDMI cable included.

Heated 18" Satellite Dish

Keep that snow off your dish antenna! This heated dish will melt the snow and prevent ice from forming on it during the winter months. Low voltage antenna heater keeps it clear of snow and ice!

Comes with 100ft. of cable, low voltage power supply, and heated dish assembly which includes an automatic heating element. It turns itself on when weather conditions are favorable for ice and snow.

This item does not include an lnb.

This unit is a definite upgrade over the very popular Nfusion Nova and Nfusion Solaris.

TECHNICAL SPECIFICATIONS

• 1 Input Connector : F-type,IEC 169-24 
•  IF Input Frequency : 950MHz to 2150MHz 
•  IF Loop Throughout : 950MHz to 2150MHz 
•  Input Level : -65 dBm~-25 dBm 
•  DiSEQqC Control : 1.0, 1.2 & USALS Compatible 
•  Band Switch : 22KHz Tone(22 +/- 4KHz. Amplitude : 0.6 +/- 0.2V) 
• Symbol Rate : DVB-S QPSK : 1-45Msps 
•  Input Voltage : AC 100~250V, 50/60Hz 
• LNB Power : 13 /18VDC / 1,000mA Max
  
  MPEG TRANSPORT STREAM A/V DECODING
• Aspect Ratio : 4:3, 16:9 
•  Audio Decoding : ISO/IEC13818-3(MPEG2 Audio/MUSICAM)
•  Audio Mode : Stereo, Main, Sub 
• Video Output : RCA, Component, S-VHS (S-Video)
  
  MICROPROCESSOR & MEMORY
   
• Main Processor : LSI 
•  CPU Speed : 108 MIPS 
•  Flash Memory : 2 MB + 1 GB (Nand flash memory) 
•  SDRAM : 18 MB + 2 MB
  
  DATA PORT
  
•  Connector : 9 Pin D-Sub Type 
•  Protocol: RS232 Asynchronous
•  Data Rate: Max. 19.2Kbps 115.2K
•  Ethernet : 10BaseT/100BaseTX
  
  A/V OUTPUT
  
•  Component output : Y/Pb/Pr (RCA) 
•  Video : CVBS output (RCA) 
•  Audio : Stereo L/R output (RCA) 
•  S-VHS : S-Video 
•  Digital Audio : 1 optical output, S/PDIF
  
  FRONT PANEL
  
•  Smart Card : 1 Slot
• 7 keys : Menu, OK, Power, Channel Up/Down, Volume Up/Down
  
  REAR PANEL
  
• Ethernet port 
•  IF Input: F-type Connector 
•  Loopthrough Output: F-type Connector 
•  Component output : Y/Pb/Pr 
•  S-VHS : S-Video 
•  3RCA : Video, Audio L, Audio R 
•  S/PDIF (Optical) for Digital Audio AC-3 Bitstream Output 
•  RF Modulator: 3-4 CH 
• RS232 Serial Port : 9 Pin Connector, D-Sub Type, Twisted Cable 
•  Power On/Off switch

This multi-switch is used.  This switch is guaranteed to work on arrival.

This multi-switch works with Dish 300 and Dish 500 satellite systems.

Can also be used to cascade additional DP34 multiswitches for more receiver outputs. Can only be used with DishPro LNBFs.

Switch has 3 trunk outputs for cascading to an additional DP34 switch for more outputs

Can be used indoors or outdoors

Does not require power insertion / power supply

Four outputs for connection to up to four Dish Network satellite receivers

Three satellite inputs for use with up to three orbital locations

The first switch in the new DishPro Technology series of LNBFs and switches

This is a used dish network lnbf.  This item is guaranteed to work on arrival.

Dish Network Dish Pro Quad LNBF

Built in multiswitch combines DISH Network satellites 110 and 119 for outputs up to four satellite receivers.

• Receives signal from both 119 and 110 satellites
• Replacement head for DISH Pro 500 satellite antenna system
• For use with DISH Pro receivers
• Can also use DP34 Multiswitch to add receiver outputs

This is a used DP-21 switch.  This is guaranteed to work on arrival.

A DishPro 21 (DP21) Multi-Dish Switch allows you to receive signals from two DishPro LNBF's and send these signals to a DishPro satellite receiver.

Use this switch to combine a Dish500 with a Dish300 or combine two Dish300's together. Both LNBF's and all receivers must be DishPro Series. You can't combine older Legacy LNBF's with DishPro LNBF's. This is a lower cost solution compared to adding the SW34 Switch. ONLY use the DP21 with DishPro LNBF's, like DishPro Twins and Quads, DishPro Receivers and non-DishPro receivers equipped with the DishPro Adaptor.

The DP21 switch is designed for outside use.

SL3  Directv Slimline LNBf for 99, 101, and 103 Satellites

This lnbf fits directly on to your slimline dish antenna.   

This multi-switch is used.  This switch is guaranteed to work on arrival.

This multi-switch works with Dish 300 and Dish 500 satellite systems.

Can also be used to cascade additional DP34 multiswitches for more receiver outputs. Can only be used with DishPro LNBFs.

Switch has 3 trunk outputs for cascading to an additional DP34 switch for more outputs

Can be used indoors or outdoors

Does not require power insertion / power supply

Four outputs for connection to up to four Dish Network satellite receivers

Three satellite inputs for use with up to three orbital locations

The first switch in the new DishPro Technology series of LNBFs and switches